Rear differential bushing replacement in BMW E46 with TED99705 puller - TEDGUM

Rear differential bushing replacement in BMW E46 with TED99705 puller

This manual shows step by steps how to replace the rear differential bushing 00082043 using the TED99705 puller on a BMW E46.

1

obraz obsługa ściagacza TED99705 1 — Drop the rear muffler from the rear hanger and place it on a support.

2

obraz obsługa ściagacza TED99705 2 — Remove the heat shield that is over the exhaust.

3

obraz obsługa ściagacza TED99705 3 — Unscrew the bolts on the stabilizer cushion clamps.

4

obraz obsługa ściagacza TED99705 4 — Unscrew the axle shafts from the differential.

5

obraz obsługa ściagacza TED99705 5 — Unscrew the rear aluminium differential bracket.

6

obraz obsługa ściagacza TED99705 6 — Unscrew the driveshaft from the differential.

7

obraz obsługa ściagacza TED99705 7 — Place the differential on the support.

8

obraz obsługa ściagacza TED99705 8 — Unscrew the rear differential bushing.

9

obraz obsługa ściagacza TED99705 9 — Unscrew the two screws on the front differential bushings and remove the differential.

10

obraz obsługa ściagacza TED99705 10 — The old bushing that will be replaced.

11

obraz obsługa ściagacza TED99705 11 — Mount the puller.

12

obraz obsługa ściagacza TED99705 12 — Pull out the old bushing.

13

obraz obsługa ściagacza TED99705 13 — Before installing the new bushing, clean and lubricate the socket.

14

obraz obsługa ściagacza TED99705 14 — Put the puller together with a new bushing. Remember to place it correctly in the socket. The bushing is not symmetrical.

15

obraz obsługa ściagacza TED99705 15 — Pull in the bushing. The bushing is correctly pressed in.

Download this manual in PDF

Manual shown above is just a presentation showing how the repair procedure can be made. TEDGUM® company does not bear responsibility for any errors in the manual and incorrect interpretation of the manual. Repair should be preceded by skilled personnel with the use of appropriate tools and with keeping all the safety means. All rights reserved.

More in this category

Replacement of metal-rubber-metal bushing with metal-polyurethane or metal-rubber non-glued manual(Manual #17)

2022-04-04

Some bushing can be available in construction composed of 2 elements. This solution is more popular for polyurethane bushings, but

Disassembly of the metal-rubber-metal bushing and assembly of the metal-polyurethane bushing (2 halves) without the outer sleeve (Manual No. 24)

2022-02-17

The following instructions show how to properly replace a metal-rubber-metal bushing with a metal-polyurethane bushing consisting of 2 halves and

Manual for the puller TED97715

2021-09-06

Bushings puller TED97715 for the bushing 00503549 in Opel Astra H and Opel Zafira B. The puller allows the correct

Removal of metal-rubber-metal bushing and installation of non-glued metal-PU or metal-rubber bushing (Manual No. 16)

2021-08-27

How to correctly replace 3-parts bushings? Before replacing Removal process 1 Remove the inner sleeve with the rubber, leaving the

Correct way to install metal-polyurethane bushings (with 2 flanges) (Manual No 15)

2021-07-30

Very often, in the case of polyurethane bushings, there are 2 polyurethane parts with flanges, inside which a metal sleeve needs to be pressed.